If any defect are found, replace the exhaust old sealer from the exhaust pipe and muffler. B933H21506009 Inspect the oil tank oil leaks. Save thousands of dollars by being your own mechanic with the help of this manual!. If any defects are found, replace the cylinder with a new one. Special tool A : 09900—20803 Thickness gauge B : 09900—20205 Micrometer 0 —. Replace any Measure the valve stem O. Replace the bearing if there is anything unusual.
I933H1520044-02 7 Install the oil seal retainer 4. Install the swingarm in the reverse order removal. If any defects are Installation found, replace the boot with a new one. Inspect valve clearance Initially at 1 month and every 6 months thereafter Inspection Tappet clearance adjustment must be checked and adjusted, a at the time of periodic inspection, b when the valve mechanism is serviced, and c when the camshafts are removed for servicing. It covers every single detail on your vehicle. Each section of this manual provides comprehensive information on the operation of major systems, diagnostics, troubleshooting, overhaul, as well as the removal and installation of major components.
Brake hose union bolt 7. This is an Instant Download Manual, no waiting for the Mail Man! B : 09900—20701 Magnetic stand C : 09900—21304 V-block 100 mm Swingarm pivot shaft runout Service limit: 0. Many mechanics purchase electronics manuals like this and use a laptop near them while doing maintenance! This will squeeze out oil trapped between the shim and the tappet that could cause an incorrect measurement, then check the clearance again to confirm that it is within the specified range. Pay attention to the following points: Apply engine oil to the O-rings. Removal Remove the footrests 1 , left and right. Tightening torque Gear position switch mounting bolt a : 6. If the commutator is abnormally worn, replace the armature.
Step Action Check the ignition system couplers for poor connections. At the same time, Honda offered another surprising manual hybrid: the original Civic Hybrid, which could be had with a stick from 2003 to 2005. Removal Oil seal 1 Remove the transmission assembly. Poor contact of generator lead wire Repair. Inspect the radiator reservoir tank in the following 2 Apply thread lock to the reservoir tank mounting procedures: bolts and tighten them. Compression Pressure Check B933H21404002 The compression pressure reading of a cylinder is a good indicator of its internal condition. I933H1520042-01 3 Install the bearing retainers 2.
Removal 1 Disconnect the clutch cable 1 and parking brake cable 2. I933H1160011-02 Installation Install the radiator in the reverse order of removal. If any : Grease 99000—25160 Water resistance defect is found, replace the chain buffer with a new one. This is the same manual dealerships use to repair your atv. B933H29206008 If any abnormality is found, replace the handlebar Inspect the dimmer switch in the following procedures: switch assembly with a new one.
I933H1530049-01 I933H1530046-01 22 Install the rear brake pedal. Special tool : 09900—06107 Snap ring pliers 2 Remove the oil pump idle gear 2 and oil pump driven gear 3. Gear position switch 1 Remove the gear position switch 1. Support the valve using V-blocks, as shown in the figure, and check its runout using the dial gauge. The removed snap ring 14 must be replaced : Thread lock cement 99000—32110 with a new one. Pay attention to the following points. If any damage is found, damage.
The Clymer online manual is excellent for viewing on tablets such as the iPad. Replace the oil seal that shows indications of leakage. Removal 1 Remove the fuel tank cover. I933H1520022-01 I933H1520019-02 2 Install the reverse idle gear 3 and shaft 4. I933H1520058-01 6 Remove the gearshift pawl lifter 8 and gearshift cam driven gear 9.
The thickness of the is out of specification, replace the valve with a new one. Replace the new O-rings with new ones. When you have driven it awhile and then shut it off it acts like it is difficult to turn over, you can let off of the key and try again and usually it will turn … 2012-04-26 17:57:09 Daily Kos A tag is a way to search for this diary. You can reading 2003 suzuki ltz 400 service manual online or load. B933H21606005 Removal 1 Remove the side covers, left and right. Remove the starter torque limiter 1. The periodically filed data help improve the accuracy of troubleshooting since they can indicate the condition of vehicle functions that has changed with time.
Tightening torque Primary drive gear nut a : 140 N·m 14. I933H1530027-01 9 Remove the spring washer 7 and its seat 8. For this purpose, use of an inspection form such as below will facilitate collecting information required for proper analysis and diagnosis. The engine starts fine when it is cold. Parking knob : Apply grease. This manual pdf download is a great guide to help you carry out simple or more advanced maintenance and repair work efficiently and correctly.