Caterpillar 3406c service manual. Caterpillar CAT 3406C Generator Set Parts Manual 2019-01-25

Caterpillar 3406c service manual Rating: 8,7/10 1048 reviews

Caterpillar Cat 3406c Generator Set Parts Catalogue Manual Download

caterpillar 3406c service manual

April 1988 Update: Improvements to torque map for 425 hp rating. Bell crank 3 is used to transfer linear motion of the timing advance unit to the end of Timing Position Sensor 2. This can be done as follows. These procedures are included in this manual. Tons of pictures and diagrams at your fingertips!! No more flipping through books to find what you need. See Illustration 3, Item 8.

Next

Caterpillar CAT 3406C Generator Set Parts Manual #2

caterpillar 3406c service manual

It covers every single detail on your Caterpillar Cat 3406c Generator Set Parts Catalogue. The thrust bearing is fastened to the timing advance body assembly 10 and the thrust bearing follows the movement of the timing advance body assembly 10. See Illustration 3, Item 7. No more flipping through books to find what you need. The fault should be eliminated. This adjustment may have to be performed several times before both low and high idle adjustment ranges are achieved at the same time. Top View Of Barrel Right G.

Next

Cat 3406C Service Manual

caterpillar 3406c service manual

The overall effect is a speed burp and a speed surge that is felt by the driver. The chances of a rack or timing sensor failing in a manner which prevents an engine from starting is very remote. This failure mode usually shows up as a 40 to 60 wheel horsepower loss at rated conditions. Try using another service tool cable. Use the standard bushing tightening torque of 260 N·m 190 lb ft in all other cases.

Next

Caterpillar Cat 3406c Generator Set Parts Catalogue Manual Download

caterpillar 3406c service manual

Each section covers a specific component or system with detailed illustrations. When troubleshooting these faults, try to recreate the conditions in which the fault occurred. The remote mount oil kit may or may not already be installed on the engine. Bolts 11 pull rings 6 and 12 together in order to hold gear 7. Keep this shop manual handy and use it often.

Next

Caterpillar Cat 3406C Marine Engine

caterpillar 3406c service manual

The required replacement parts are listed below. The most common fixes for the above listed problems are as follows: - Personality module seal or module cover seal. If a timing sensor has a loose tip, clean the tip, apply primer, and Loctite the tip back on the sensor. P-222: Engine Speed Sensor Test 11. Check for proper installation and operation of shutdown devices. See Illustration 1, Item 1. Shutoff solenoid Page 3 of 85 d.

Next

Caterpillar 3406C Diesel Engines Factory Service & Shop Manual • PageLarge

caterpillar 3406c service manual

Acceleration rate limiting above 1500 rpm is eliminated. Some of the more common problems that are associated with the Engine Speed Sensor are as follows: - - Sensor filling with oil and pushing out into cam gear. November 1987 Update: Improve customer specified parameter fault detection. It is great to have, will save you a lot and know more about your Caterpillar Cat 3406C Marine Engine, in the long run. Page 15 of 85 Locations to add oil for dipstick calibration. This entry was posted in and tagged , on by.

Next

Caterpillar CAT 3406C Generator Set Parts Manual #2

caterpillar 3406c service manual

P-514: Boost Pressure Sensor 9. Check fuel tanks for foreign objects that may block fuel supply. This style bonnet can have staining removed with the same cleaning process and reused. The total timing advance range is 25 crankshaft degrees. .

Next

Caterpillar Cat 3406c Generator Set Parts Catalogue Manual Download

caterpillar 3406c service manual

Page 71 of 85 F. The perception of excessive oil consumption can be changed by expanding the size of the operating range. For more details on the correct throttle adjustment procedure, see the Reference. The former 9X-6770 Solenoid has been replaced by the new 105-2939 Solenoid. This outward motion of the body assembly 10 causes the fuel injection timing to be advanced. If the chopper wheel can be rotated with a screwdriver, it is too loose.

Next

Caterpillar CAT 3406C Generator Set Parts Manual #2

caterpillar 3406c service manual

Page 62 of 85 If a Remote Mount Oil Sensor Is Already Installed Illustration 1, 3406B Wiring Diagram. The 3N-2704 Mounting Plate can be used if a suitable mounting location cannot be found. If the rack is advancing but the engine does not start the fuel may begin gelling. If the fault can be recreated, follow the troubleshooting procedures. A Truck Engine News article on the Kysor Shutdown System is also included in this manual.

Next

Caterpillar 3406C Diesel Engines Factory Service & Shop Manual • PageLarge

caterpillar 3406c service manual

Codes 32 and 56 limit engine speed to low idle. Install the mechanical dial indicator on the fuel system and then move the rack manually to the point that the rack reads 1. P-512: Engine Speed Sensor 9. Replace 2W-2409 and 6I-1665 Bonnets with new 108-2102 Bonnets. Improved vehicle speed sensor diagnostics.

Next