Kawasaki prairie 360 fuse box. Kawasaki Prairie 360 4x4 Parts 2019-02-19

Kawasaki prairie 360 fuse box Rating: 4,1/10 1393 reviews

KAWASAKI PRAIRIE 360 SERVICE MANUAL Pdf Download.

kawasaki prairie 360 fuse box

Follow the wires from the tail light assembly on the inside of the rear fender left side towards the front of the bike until you come to the box connector. If the fork is bent, replace the shift rod with a new one. Pinion Gear Shim s 4. Well apply it for better future posts. If the test light does not turn on, continue the test. Slide the fender out the rear of the bike. Drive Belt Failure Detecting Switch 9.

Next

Kawasaki Atv Prairie 360 Wiring Diagram

kawasaki prairie 360 fuse box

Screw the camshaft sprocket bolt in to the end of the camshaft and pull it with the camshaft. Sheave Bushing Inside Diameter Standard: 39. This picture has been uploaded by Maria Nieto tagged in category field. Do not forget to share and love our reference to help further develop our website. If any wiring is defective, replace the damaged wiring.

Next

KAWASAKI PRAIRIE 360 SERVICE MANUAL Pdf Download.

kawasaki prairie 360 fuse box

Oil Cooler Fan Fuse 20 A 10. No liability can be accepted for any inaccuracies or omissions in this publication, although every possible care has been taken to make it as complete and accurate as possible. Flying debris could cause serious eye injury. Make sure as you hide the cord on the way to the battery, that your handlebars turn freely and that the cord does not come in contact with hot engine parts that may melt the wire over time. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame.

Next

Kawasaki Prairie 360 4x4 Parts

kawasaki prairie 360 fuse box

Parking Brake Lock Lever 6. If the vacuum piston does not move smoothly, or if it is very loose in the carburetor body, replace both the body and the vacuum piston. Check the measurements below and if these holes already exist at the proper distance, remove any existing mounting hardware from the holes and secure the box with the supplied mounting hardware. Starter Circuit Relay Brake 10. Drive Belt Failure Detecting Switch 8. The surface of the piston must not be excessively worn.

Next

Kawasaki ATV Forum

kawasaki prairie 360 fuse box

Remember me telling you his kept blowing fuses. Rear fender — Remove the rear fender, by first disconnecting the taillight wires. The bike should only be raised enough to relax the tension in the springs. There are several parts that must be removed in order to get the air-box out of the bike in one piece. If the connector is corroded or dirty, clean it carefully. We have been searching for this picture throughout on-line and it came from reliable source. Note: Bottom roller may need to be removed to run wire rope through.

Next

Kawasaki Prairie 360 Fuse Box Location

kawasaki prairie 360 fuse box

Make sure oil passages of the crank and crankpin are lined up during assembly. The fuel injection system fuse box is located under panel D. They are designed to give optimum performance while maintaining a low noise level. Do I send trevor the bill since my brute is probably what pulled him out : Sorry Trevor. Just see if you can eleminate some of the items.

Next

Kawasaki Prairie 360 Wiring Harness

kawasaki prairie 360 fuse box

Brake Pedal Light Switch 5. Note the readings total 3 measurement. If possible share this kawasaki prairie 360 vin location photo for your mates, family through google plus, facebook, twitter, instagram or another social bookmarking site. Remove the bottom and middle bumper mounting bolts. Put a little coarse grinding compound on the face of the valve in a number of places around the valve head. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts.

Next

Kawasaki Atv Prairie 360 Wiring Diagram

kawasaki prairie 360 fuse box

This allows some of the compression pressure to escape, making it easy to turn over the engine during starting. Input from Drive Belt Failure Detecting Switch 10. Drive Pulley: Cover bushing inside diameter. The output driven bevel gear shaft assembly comes off with the housing. Underneath the side cover there are three rubber grommets 1 on the frame tab, and two on the air-box that support the side cover.

Next

Kawasaki Prairie 360 Fuse Box Location

kawasaki prairie 360 fuse box

Peel the remaining half of the liner from the gasket backing, and carefully position the rest of the gasket to the door frame. If a headlight bulb burns out, replace it as follows. If the mufflers are not removed, they can become damaged by the axles in Section 2H. When using a battery charger, connect the battery to the charger before turning on the charger. Install the winch to the bottom of the mount using the hardware provided with the winch. If necessary, replace the belt with a new one. Pinion Gear Shims for Tooth Contact Adjustment Thickness Part Number 0.

Next