Is there a pump in the bottom of the outdrive that could be my problem? I added gear oil and serviced the bottom and all greese fittings. Here you are at our website. Did you fill it from the Bottom,. Many boats have room to pull the engine forward and off the shaft of the outdrive. I guess I was told wrong. I hadnt ran the motor long like that, so hopefully its ok.
You can also find other images like wiring diagram, sensor location, fuel pump location, starter location, control module location, parts diagram, replacement parts, electrical diagram, repair manuals, engine diagram, engine scheme, wiring harness, fuse box, vacuum diagram, timing belt, timing chain, brakes diagram, transmission diagram, and engine problems. After reading the manual you will see the correct way is to remove the outdrive first, and then the engine. And you know, when I first found it, we loved it, we hope you are too. And how hot should the exhaust elbo get? My Upper drive unit was bone dry. Users have access to complete engine maintenance and repair information along with quick access buttons to Maintenance Schedules, Wiring Diagrams, Parts, Specification Charts, and a hyper-linked index.
I just thought I needed to replace the motor because of the cracked block. I dont know how to check the alignment. Did you check the gimbal bearing and ujoints? I would appreciate any info about these issues. I would like to know about alignment as well. If you prefer traditional service manuals Seloc also offers a full line of printed engine repair and maintenence guides. You have to then move the motor up down sideways when you read the alignment bar. Is there a constant significant flow of water, or just when the thermostat opens? It's all in the manual.
Inboard , , , Mercruiser Gas 5. I am thinking that I need to service my outdrive. How do I check the bearing? When I fired it up, it runs great and after about a miniute, a noise started from what seems to be where the motor shaft goes into the outdrive. Then I removed the top cover to pump out the old oil, and there was none. Do you think its quite possible the noise im getting is due to allignment? What kind of greese do I need for the spline shaft? It still makes the noise. Yeah, I drained the lower section, and it had milkey nasty oil. Ask questions as you go along and someone will be along to help.
I think im not getting proper water flow. After reading the manual you will see the correct way is to remove the outdrive first, and then the engine. I hope It isnt to late. No, I was not sure what to check. ?? Ask questions as you go along and someone will be along to help. Regarding Photo detailed description: Graphic has been uploaded by author.
What you have already discovered is that it is physically possible to remove and install the engine without removing the outdrive. We determined this on the net sources and we suppose this can be one of many excellent content for reference. I am totally new to boats, but I am a machanic. I dont know how to check those things. We thank you for your visit to our website. . I filled it from the bottom.
Many boats have room to pull the engine forward and off the shaft of the outdrive. It makes this noise that sounds like roller skates, but on a much louder scale when the motor is running. How much water should come out while running the motor? Do not forget to share and love our reference to help further develop our website. Today were pleased to declare we have found an awfully interesting niche to be discussed, namely 165 hp mercruiser engine diagram. Did you run it without water going to the drive?? I did not know that the spline shaft needed greese. There are a few the reason why you are interested in details about 165 hp mercruiser engine diagram, and surely, you are researching for fresh concepts for your needs. Did you take the outdrive off before you put the engine in? Make sure you get the information you are looking for.
Also, my outdrive is a 160 mercruiser stern drive. I guess I should have gotten a manual before starting this project. Did you run it with no gear oil in it? Must I remove the engine again, or can I just remove the outdrive, and align the motor, then re-install the outdrive? Many people attempting to find info about 165 hp mercruiser engine diagram and certainly one of these is you, is not it? I was told just to slide the old motor out and the new one in. When put into gear, it works fine. Im not sure I am looking at the correct mannual. I guess I should get a manual to do it right. That's usually a Bad thing,.