Use transom drilling fixture 91-98234A2 or attach tape engine mounting template lo- cated in the installation manual to boat transom. Install throttle cable to the throttle arm with hairpin cotter. Install the top half of the cable clamp and reinstall the cowl bracket. Special Bolt 10-856680 Torque to 27. The most important tool in your toolbox may be your Clymer manual -- get one today. Secure propeller nut to the shaft with cotter pin. Install the outboard so that the anti-ventilation plate is in-line with the bottom of the boat.
Cable Barrel Hair Pin Cotter 6. Use the original propeller hardware or order replacements for worn or damaged parts. Is this normal for the Deep V boat? Install plastic spacer, o-ring and two flat washers and nylon insert locknut cap onto steering cable as shown. Adjust the cable barrel until the alignment mark on the cam lines up with center of the roller. Great for aluminum console, deck, inflatable rigid hull, inshore fishing, offshore fishing, and runabout boats and tritoons.
Description Where Used Part No. Failure to correctly fasten outboard could result in out- board ejecting off boat transom causing serious injury, death, or property damage. Disconnect all of the battery leads from the battery. How do I adjust the position of shift shaft on a 1995 15hp mariner how do you install a water pressure gauge on 2002 mercury 15hp 2 stroke how do you take a lower unit off 1995 15hp mariner motor how to adjust a throttle on 15hp yamaha outboard how to adjust air screw on 97 mercury 15hp how to adjust carburetor on 15hp yamaha how to adjust idle on 1987 evinrude 15hp. How do I stop the over spray? Bundle the fuel line, battery cables and wiring together and wrap with the piece of foam provided as shown.
Adjust cable barrel so it slips freely into the barrel holder. If the filter appears to be contaminated, remove and replace. Slide the rigging tube onto the cable clamp and fasten with collar and hose clamp. I put it in the water this past week for the first time. Lift rear of cowl and disengage front hook. Spark plug Lubrication Points 1. Install steering link rod to rear hole on steering arm per illustration.
Special trim tab or anodic plate may need to be purchased separately for propeller clearance. Push-in on the cable end until resistance is felt. With many outboard options on the market, identifying the best engine for your current boat can be daunting. Insert steering cable into tilt tube. Unlock the rear latch by pushing lever down. Always disconnect the battery cables from the battery before maintaining, servicing, installing, or removing engine or drive components.
How to adjust throttle on 15 hp 1978 yahama how to change a throttle link for 1979 mercury 15 hp 4 stroke 1980 how to change the impeller in a 15 hp mercury how to check gear oil level on 1981 mariner 15 hp how to check oil level 1982 johnson 15 hp 4 stoke how to check oil level on a 15 hp 1983 johnson outboard engine how to clean a 04 yamaha 4 stroke 15 hp outboard motor carburator how to flush a suzuki 15 hp outboard. These points should be lubricated at least once a year by an authorized dealer. Description Where Used Part No. Check throttle cable adjustment as follows: a. Place cable barrel into the bottom hole in the bar- Install cables into the remote control following the rel holder. Improper installation or servicing of the Mercury product could result in damage to the product or personal injury to those installing or operating the product.
If contaminated oil is noticed, have the engine checked by your dealer. Suzuki 15 hp outboard oil filter location suzuki 15 hp outboard water flush port suzuki 15 hp repair manual suzuki 15 hp spark plug gap suzuki 4 stroke 15 hp outboard motor oil trouble with 15 hp yamaha floats troubleshoot air pressure sensor price on 15 hp yamaha outboard tune up spec yamaha 2006 15 hp outboard utube 2007 mercury 4 stroke 15 hp water pump valve adjustment mariner 15 hp outboard. Install thrust washer, propeller, propeller nut re- tainer, and propeller nut onto the shaft. Place outboard in a vertical operating position. Install the vent plug and sealing washer before removing the lubricant tube.